ATTENTION

This FlexSim Community Forum is read-only. Please post any new questions, ideas, or discussions to our new community (we call it Answers) at https://answers.flexsim.com/. Our new Question & Answer site brings a modern, mobile-friendly interface and more focus on getting answers quickly. There are a few differences between how our new Q&A community works vs. a classic, threaded-conversation-style forum like the one below, so be sure to read our Answers Best Practices.


flexsim.com

Go Back   FlexSim Community Forum > FlexSim Healthcare (HC) > FlexSim HC: Q&A
Downloads

FlexSim HC: Q&A Questions about FlexSim Healthcare

  #1  
Old 02-05-2010
Lionel Lim Lionel Lim is offline
Flexsim User
 
Join Date: Oct 2009
Posts: 6
Downloads: 0
Uploads: 0
Thanks: 5
Thanked 0 Times in 0 Posts
Rep Power: 0
Lionel Lim is on a distinguished road
Default How to assign more than one physician to a specific bed?

Hi

I wish to simulate 2 doctors using a consultation room for the morning and afternoon shift. I have a bed/examination table as my patient processing object, and would like to assign the 2 doctors to that bed in shifts (morning and afternoon). How do I go about doing so?

Lionel
  #2  
Old 02-06-2010
Lionel Lim Lionel Lim is offline
Flexsim User
 
Join Date: Oct 2009
Posts: 6
Downloads: 0
Uploads: 0
Thanks: 5
Thanked 0 Times in 0 Posts
Rep Power: 0
Lionel Lim is on a distinguished road
Default How to make the Doctors stay at the particular bed for the duration of his shift?

Hi again

I have used the shift schedules function to assign each doctor to a particular work schedule. However, I have run into 2 problems:

1. How do I assign them to a particular bed for their shift?

2. How do I keep each doctor at his assigned bed for the duration of his work schedule?

Thank you very much for taking the time to help!

Lionel
  #3  
Old 02-10-2010
Rachid Kolfin Rachid Kolfin is offline
Simulation Consultant
 
Join Date: May 2008
Location: Amsterdam
Posts: 21
Downloads: 18
Uploads: 0
Thanks: 58
Thanked 37 Times in 16 Posts
Rep Power: 169
Rachid Kolfin will become famous soon enoughRachid Kolfin will become famous soon enough
Default

Hi,

I am not exactly sure if I understand your question. It seems to me that when you define one BedArea (with more than 1 bed) and one PhysicianGroup (with more than 1 physician) you are able to assign individual physicians but also individual beds to the schedules. So if you define two seperate schedules in wich the physicians and beds are matched it should work. So during one shift only one physician group and one "Bedgroup" will be available.

You could use the downfunction to make the doctor stand by a bed.

I hope this can help you.

Good luck,

Rachid Kolfin
The Following User Says Thank You to Rachid Kolfin For This Useful Post:
Lionel Lim (02-22-2010)


Thread Thread Starter Forum Replies Last Post
Assign Operators to Scheduled Down Time jspeece Q&A 1 09-04-2009 01:47 PM
Call a specific operator Michael Hartlieb Q&A 3 06-29-2009 09:04 AM
make transporters cycle a specific path bsantens Q&A 4 10-21-2008 08:08 AM
Close A Specific Port Joe Allen Q&A 2 09-11-2008 06:30 PM
Assign an array to a variable AlanZhang Q&A 6 04-24-2008 01:59 PM


All times are GMT -6.
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
Copyright 1993-2018 FlexSim Software Products, Inc.